![]() ![]() I have a block of 8 IP addresses, I have one specific 'public IP' over which I am trying to link via IPSec to a remote site (not mine).I'm trying to configure a static ipsec tunnel between an SRX240 and a Linux host (using racoon). Local IP : 1.2.3.4 (well it isn't but just for example) The vendor at the other site has configured this specific public IP address 1.2.3.4 as his remote endpoint. INFO: IPsec-SA request for 2.3.4.5 queued due to no phase1 found.īut the log shows that it is using 5.6.7.8 as my identifier as shown by the error The problem - my IPSec is failing Phase 1 with the error My DSL modem connects to the ISP and uses the public facing address of 5.6.7.8 I have configured the 'My Identifier' section of the IPSec phase 1 configuration to be IP Address (NOT My IP Address) and entered 1.2.3.4 in the box to its right. Racoon: : INFO: 5.6.7.8 used as isakmp port (fd=14) This is wrong, this is NOT what I need - does the My Identifier IP address option work?Īm I going nuts or should I be seeing racoon: : INFO: 1.2.3.4 used as isakmp port (fd=14) as part of the phase 1 negotiation and in accordance with the My Identifier setting.Ĭan anyone point me in the right direction please. I can now confirm that this IS a problem in pFsense. I spent 4 hours playing (I had a Cisco man monitoring the foreign system) we confirmed 100% that pFsense never presents the correct identifier during phase 1 negotiation. There seems to be no way to get pFsense to present the IP address specified in the phase 1 setup 'My identifier' section - it ALWAYS presents 'My IP Address' (in my case the IP used by my DSL modem / WAN) the nf file is correct and points so my feeling is that this piece of code is broken. #Ipsecuritas could not start racoon code# The proof that this setting is the problem - When we configured the foreign system to expect my 'DSL Modem/WAN' IP the IPSEC works fine and the tunnel was up straight away. I have a similar problem, but in my case I have two wan connections each with its own WAN IP going back to the same remote site, configured with two different tunnels. I setup FQDN's as the identifiers but with no results. I can establish the the first Tunnel without a problem, but the second tunnel always fails phase 2 because phase 1 is incorrect. Racoon: : INFO: initiate new phase 1 negotiation: 1.1.1.12.3.4.5 Oddly enough if I enable the second tunnel first then start the first tunnel and everything is great until the timetolive expires then I have the same problem. Racoon: : INFO: initiate new phase 1 negotiation: 2.2.2.22.3.4.5 Then tunnel 2 initiates and I get this, which never establishes unless I enabled it first. Racoon: ERROR: none message must be encrypted Racoon: : INFO: IPsec-SA request for 2.3.4.5 queued due to no phase1 found. Racoon: ERROR: phase1 negotiation failed due to time up. Racoon: : ERROR: phase2 negotiation failed due to time up waiting for phase1. Racoon: ERROR: ignore information because ISAKMP-SAhas not been established yet. Racoon: : WARNING: the packet retransmitted in a short time from 2.3.4.5 Racoon: : NOTIFY: the packet is retransmitted by 2.3.4.5 (1). Racoon: : INFO: initiate new phase 1 negotiation: 2.2.2.22.3.4.I finally got this flaming POS working on Windows 10 along with the DLC. #Ipsecuritas could not start racoon windows 10# I tried about 100 different guides, tips and tricks to the letter and nothing seemed to work. Through hours of trial and error I got it working. ![]() #Ipsecuritas could not start racoon trial# You don't need to download modified DLL's this way either. Like the guides here on steam, you have to uninstall your current "GfWL" and "Market Place" through Add/Remove Programs. Once uninstalled I installed the following three things.ġ:V Microsoft download link no longer available. The game will work if you just install GfWL, but the DLC will not.Ģ: Right click on REORC, click on the LOCAL FILES tab, click on VERIFY INTEGRITY.ģ: Click on the DLC tab, uncheck all of the DLC's. #Ipsecuritas could not start racoon install# (It will do a small update after they are uninstalled)Ĥ: After the small update, reclick on all of the DLC's. ![]() #Ipsecuritas could not start racoon update# (this will be a larger update, 2.1gbs or so)ĥ: Click on the LOCAL FILES tab again and click on the BROWSE LOCAL FILES button.Ħ: Inside the local files, right click on "RaccoonCity.exe" and select "properties".ħ: Click the "Compatibility" tab and check the "Compatibity mode" box and select "Windows 7"Īlso check the "run as administrator" box. (click OK to close)Ĩ: Open "My Documents" and delete the "RERC" folder inside of the CAPCOM folder.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |